Crimping Tools & Accessories

CD178-255 CRIMPING DIE


For Type 734/735 Cable
FEATURES   
Precision machined for accuracy Heat treated tool steel for longevity
CCT601 CRIMPING FRAME
Perfect for high speed telecommunications
such as T1 and DSX and CATV. Reduces carpal tunnel syndrome. Tool is calibrated to appropriate closure force. Can be used with
CT4 Pneumatic Tool Holder
FEATURES   
Lower handle force. Ergonomic. Manually crimp coaxial connectors to manufacturer’s specifications. High quality crimps. Reliable and durable. Can be used with die sets for BNC, TNC, Type N, CATV “F”.
CCT602 CENTER PIN CONTACT CRIMPER
Designed for center pin contact crimping. Multi point indent crimper. Industry standard Central Office (CO) tool. Provides 3 rows of indentations at 90 degrees to each other around the center contact pin. Crimp contacts on coaxial and triaxial cable.
FEATURES   
Ratchet mechanism releases only after proper crimp force is applied Locator holds contact in place during crimping Built in locators provide fast, precise contact alignment Full cycle ratchet Tool steel frame and rust resistant black oxide finish Cushioned vinyl handles Specifications: 6-1/2″ length, pin gauge 26-20 AWG, 1/2 lb. wt.
CT-6 & CT-6ST COAX CABLE TESTERS
The CT6 Coax Cable Tester checks the continuity of coaxial cable runs terminated with BNC, F or TNC connectors. This simple tester is a fast way to determine if a coaxial cable is good, open or shorted. The CT6 comes complete with a handy carrying case and terminators for BNC, TNC, and F connectors to allow for easy testing of terminated cables.

CT – 6 COAX CABLE TESTER
TEST OPERATION   
The CT6 Coax Cable Tester is actually three independent testers. One is for BNC cables, another is for TNC cables and a third is for F type cables. Plug the included BNC, F, or TNC terminator into the far end of the coaxial cable, then connect the near end of the cable to the tester with the same type of connector as the terminator. Observe the LED corresponding with type of cable being tested (BNC, TNC, or F). If the LED is RED the cable is shorted or bad. If the LED remains UNLIT then press the test button. The LED for the corresponding connector should light GREEN showing a GOOD cable. If the LED remains unlit either the center conductor or the shield connection is open, or the terminator is not installed. If the LED light is RED there is a short between the center conductor and the shield. The terminator on the cable being tested should be the same type as the connector on the tester. This tester will not test cables with a BNC on one end and a TNC or F on the other, unless you use an optional adapter, such as BNC M to TNC F adapter. REMARKS: The tester runs on one 9 volt battery. Please make sure the battery charge is sufficient otherwise the LED will dim and difficult to read. WARNING !
Never connect this tester to a live wire. Doing so may damage
the tester or the equipment the cable is connected to.
CT-6ST COAX CABLE TESTER     
INSTRUCTIONS Important: – Do not connect the CT-6ST cable tester to a live cable
CT-6ST Coaxial Cable Tester
FUNCTION TEST:
Press and hold the button switch on the function plate to activate the tester. Only the green LED will be lit to indicate the “open” situation on the end of the connector. This will also indicate that the batteries are active. It the green LED does not light, replace the batteries. Slide the receiver out from the slot of the transmitter. Plug the receiver and transmitter onto each other. Press and hold the switch, the indicators will display an “OK” situation.
OPERATION:
To test, slide the receiver from the slot of the transmitter. Plug the receiver and transmitter on each end of the testing coaxial cable. Press and hold the switch; the LED indicator on the transmitter will display the test result as follows: “OK”, Two LED’s (red and green) will blink alternately. “Short”, Two LED’s will both lite up constantly. “Open”, Only the green LED will light up. Relieve the switch to turn off the tester. Slide the receiver back to the slot of the transmitter for storage.
BATTERY REPLACEMENT:
If the LED indicators become weak or sluggish in performance, the batteries should be replaced. The procedure is as follows: Slide the receiver out to locate the battery door on the transmitter side. Slide the battery door and replace with 2-1.5 volts AG13 Button Call batteries. Observe the correct polarity. The positive port is toward the face of the LED’s. Slide the battery door in place.
CT100 SERIES – THERMAL WIRE STRIPPERS
CT100-10
Thermal Wire Stripper
PVC 14-30 AWG
CT-100-10 Thermal Stripper
Dimensions: 4.3″ (110mm), x 2.00″ (51mm) x 1.8″ (46mm) Weight: 13 oz. (.37kg) Line Cord: #18AWG 2wire flexible cord, 6′ (1.8m) long Nichrome heating element Heats up quickly, less than 5 sec. Optimal temp. 450F Will strip insulation from solid, stranded or shielded wires from #14 to #30 AWG Power Consumption 3 watts Eliminates nicks and broken strands of conductors
CT100-25
Thermal Wire Stripper
PVC 10-14 AWG
CT-100-30 Thermal Wire Stripper
Dimensions: 5.25″ (133mm) x 2.25″ (57mm) x 2.0″ (51mm) Weight: 1 lb. (453kg) Wire Sizes: #14 to 10 AWG Element Temp: In excess of 450F
CT100-30
Thermal Wire Stripper
TEFLON 16-30 AWG
Dimensions: 5.9″ (150mm) x 2.25″ (57mm) x 2″ (51mm) Weight: 1 lb. (.453kg) Line Cord: #18AWG 2 wire flexible cord, 6′ (1.8mm) long Strips: #16 to #30 AWG solid, stranded or shielded wires Thin Nichrome heating element evaporates a negligible amount of insulation, does not require special ventilation.
CT100-30HD
Thermal Wire Stripper
TEFLON 10-14 AWG
Dimensions: 5.9″ (150mm) x 2.25″ (57mm) x 2″ (51mm) Weight: 1 lb. (.453kg) Line Cord: #18AWG 2 wire flexible cord, 6′ (1.8mm) long Strips: wire sizes #14 to 10 AWG solid, stranded or shielded wires Thin Nichrome heating element evaporates a negligible amount of insulation, does not require special ventilation.
CT100-50
Thermal Wire Stripper
PVC Coaxial RG58, RG59
Dimensions: 5.2″ (132mm) x 2.25″ (57mm) x 2″ (51mm) Weight: 1 lb. (.453kg) Line Cord: #18 AWG, 2 wire flexible cord, 6″ (1.8m) long Power consumption: 8 watts Strips coaxial cable RG58/59/62 Heating element in excess of 450F within 5 sec.